Products

3/4" Gummed Kraft Tape 500 Foot Roll Part #MS1575 Commonly used for pasting shells to give a nice even break as well as other fireworks projects. 

This refill kit has enough tubes, chemicals, and fuse to make 25 complete 3/4-Inch Stinger Missiles with silver titanium tails. But no tooling is i...

 37mm Acetal Plastic Hulls. For use with #209 shotgun primer. Empty re-loadable 37mm flare hulls. Accepts standard 209 shotgun primer. You can use...

Introducing our 37mm to 12 gauge flare adapter, designed to enhance your shooting experience. This adapter allows you to easily convert your 37mm f...

This rocket fin and nose cone set are compatible with either TU2005 OR TU2007 1oz. rocket tubes. The fin can is a snug fit, however, variances in p...

Here are several different style nose cones meant to replace the lid of a 35mm film canister. Specifically the style of 35mm film canisters commonl...

This design is a payload cup for 3"+ shells for 37mm flare launchers. 1.35" OD For 3"+ Shell WARNING! These models are likely not suitable for re...

This design is a payload cup for 3"+ shells for 37mm flare launchers. 37mm Payload Cup - 1.350"OD x 1" ID For 3" Shell Flare WARNING! These model...

37mm Payload Cups - Multiple Configurations - 1.295" OD / 1" ID   WARNING! These models are likely not suitable for real-world use out of the bo...

37mm Powder Bushing / Cup 40 Grain Capacity For Reloadable Shells For Flare Launcher Use WARNING! These models are not suitable for real-world use...

37mm 2", 3", & 5" Shell Casings Model For Flare Launcher WARNING! These models are not suitable for real-world use out of the box as a 3D-pri...

Fin set fits many fireworks bottle rocket brands.   Designed By: rebeltaz

Nose cone fits many fireworks bottle rocket brands.   Designed By: rebeltaz

Fuse plug for converting the TU2032 (.780" ID x 2" Length) into a small shell suitable for backyard displays. The fuse hole is compatible with 2-3m...

The rocket is designed to use Estes motors which are either 18mm or 24mm in diameter (B, C, D series motors). You can buy rocket motors on the inte...

The TU1375 (1" ID x 6" Length) makes a great small mortar tube along with this base and is suitable for launching small shells made from the TU2032...

Fuse plug for converting the TU2032 (.780" ID x 2" Length) into a small shell suitable for backyard displays. The fuse cavity can be packed with st...

Concept for Round shell casing filled with exploding stuff. . Great for smoke bombs and ground effects if printed using PLA. For an aerial shell pr...

Solid plug for converting the TU2032 (.780" ID x 2" Length) into a small shell suitable for backyard displays. The plug is a tight fit and can be u...

The 3D Printed Mini Shells Supplies Kit contains all of the supplies you need to assemble 100 mini-shells and 5 mini-mortars, plus it contains an a...

This wonderful Stinger Missile REFILL Kit is easy to make and it's hefty size will satisfy the need to shoot missiles in the air and put a smile on...

This spectacular Stinger Missile Kit is easy to make and it's hefty size will satisfy the need to shoot missiles in the air and put a smile on your...

Many fireworks makers have a strong preference for the drossy, consistent burn of American Visco. Unlike Chinese fuse which can at times burn so fa...

Many fireworks makers have a strong preference for the drossy, consistent burn of American Visco. Unlike Chinese fuse which can at times burn so fa...

Effect fuses, such as this Willow Diadem Fuse are used in contracting fireworks shells and rocket headings. The fuse is cut into 1/2"-1" lengths an...

4" ID x 15 inches long with wooden plug in bottom. These HDPE Mortar Tubes are Black or Orange depending on current availability. IMPORTANT: Firin...

4 inch ID x 22 inches long, approx. 1/5" wall, with fiberglass resin plug in the bottom and structurally reinforced lip to prevent fraying. Weighs ...

4-inch paper fireworks shell hemispheres. These paper hemispheres come in sets of 2 halves. They're approximately 3-5/8" in diameter before pasting...

3-11/16" spherical plastic fireworks shells, 4" in a diameter when pasted and fused. Comes in two halves, one with a 7/32" time fuse hole, one with...

4-ounce rocket tubes were specially made so that plastic ball shell #PL2020 will fit on top of them. These parallel wound tubes can also be used to...

These tubes are factory seconds from a recent production run. They have the correct general dimensions but may include small flaws such as minor si...

4-ounce rocket tubes specially made so that plastic ball shell #PL2020 will fit on top of them. These parallel wound tubes can also be used to make...

4-Ounce Core Burner Black Powder Rocket Tool Set. The set contains an Aluminum spindle and base, one solid aluminum rammer, three hollow aluminum r...

This is the exact same toolset that is included with our Model Rocket Kit. We did extensive research to design a spindle that would create a high p...

This spectacular black powder rocket is easy to make. Adding titanium gives the normally orange tail a bright silvery finish.  Each kit contains a...

This is a refill kit for our 4-oz. Black Powder Rocket Kit. It contains everything in that kit, except the tooling. This spectacular black powder ...

Make simple sugar rockets with this inexpensive kit. Each kit contains everything needed to make 25 Sugar Rockets. - Potassium Nitrate, 1 pound, (...

4" 37mm Pay Load Tubes are designed to be used with 37mm hulls. Use your own homemade black powder and load these up with your choice of Stars, Smo...

4" Paper Lift Cups 20 Pieces Part #PC1185

You'll learn fireworks shell making really fast with this kit. Plastic shells are faster and simpler to make than paper shells. This kit contains e...

Length:  100 x 4" Pieces Burn Rate: 23-24 sec/ft  Part # GN1088 Diameter: 3/32" (3mm) This visco is already cut into 4" pieces.  Bag of 100. ...

5 inch ID x 32 inches long, approx. 1/4" wall, with fiberglass resin plug in the bottom and structurally reinforced lip to prevent fraying. Weighs ...

These high-quality kraft paper hemispheres come in sets of 2 halves, they're 4-1/2" in diameter before pasting. 10 sets Part #PS2050

5" diameter when pasted and fused. Comes in two halves, one with a 7/32" time fuse hole, one with leader hook recess. Comes with fuse washers and l...

Czech Military Surplus 26.5mm Red Rain Flares, 5 Rounds- Red, Metal 26.5mm shell casings Condition: Brand new, never issued.   FL2000